Buying guide

How to Choose an Almost Heaven Sauna Cover

Updated on · By the The Sauna Solution team

Choose an Almost Heaven sauna cover by matching the cover to your sauna's outside length, width or diameter, and shape. Barrel saunas need a cover that follows the curved roof, while cabin models need a cover sized for a rectangular footprint.

On this page (9 sections)
  1. What measurements do you need for an Almost Heaven sauna cover?
  2. How does a barrel shape change the cover fit?
  3. What is the difference between a barrel cover and a cabin cover?
  4. How much extra room should a sauna cover have?
  5. Should you choose a cover or a barrel sauna roof?
  6. How should you fit and secure an Almost Heaven sauna cover?
  7. Useful products for a covered sauna area
  8. What cover mistakes should you avoid?
  9. How to choose the right Almost Heaven sauna cover

Choose an Almost Heaven sauna cover by matching the sauna's outside length, width or diameter, and shape. Barrel saunas need special attention because the roof curves from one side to the other, while cabin models have a rectangular footprint.

That shape difference matters more than the number of seats inside. Two saunas can hold the same number of people and still need very different covers because one is round and the other is boxy.

Measure the sauna before ordering. The product name alone does not tell you whether a cover will fit a specific Almost Heaven model, especially when the same brand makes both barrel and cabin designs.

Start at the outside of the structure. A tape measure around the roof and along the walls gives you the true size the cover must pass over.

Note where the cover will fasten. Straps, buckles, and fitted ends all change how much fabric needs to drop down the sides.

Think about daily use as well. A cover that you can remove and replace without strain is easier to keep on the sauna for most of the year.

Also check the site. Trees, wind exposure, and nearby structures can affect how a cover sits and how often you need to adjust it.

Once you have the length, diameter or width, and height, compare those numbers with the finished size of each cover. That direct match is the safest way to shop.

What measurements do you need for an Almost Heaven sauna cover?

You need the outside length, widest width, and overall height of the sauna. For a barrel model, record the outside diameter as well as the length from end to end.

Measure the wood and trim that the cover must pass over. Include roof boards, exterior bands, door surrounds, and any raised vents or accessories that stay attached when the sauna is covered.

Use a tape measure and write down the results in inches:

  1. Measure from the outside of one end to the outside of the other end.
  2. Measure the widest point from one side to the other.
  3. Measure from the ground or base to the highest roof point.
  4. Record the barrel diameter if the sauna has a rounded profile.
  5. Note anything that adds height or width, such as a chimney, roof edge, or attached step.

For a cabin sauna, length and width usually give you the most useful starting point. For a barrel sauna, length and diameter matter more than the flat floor footprint.

How does a barrel shape change the cover fit?

A barrel sauna needs a cover that can drape over a curved roof without excessive tension. A flat rectangular cover can leave gaps near the sides or pull upward at the roof ridge if it is not wide enough.

Picture the barrel from the end. Its roof rises in an arc, so the fabric must travel over that arc and continue far enough down both sides to protect the upper wall boards.

A cover that matches only the floor width may be too narrow. The cover needs extra width for the curved roof, side drop, and any fastening points.

The end shape also matters. Some barrel covers are made to fit rounded ends, while a general outdoor cover may hang differently around circular or curved end walls.

Check the cut and fastening method before assuming that a large cover will fit well.

If you are still deciding between shapes, our guide to What Is a Barrel Sauna? Why the Shape Is Round explains how the curved design affects the exterior.

What is the difference between a barrel cover and a cabin cover?

A barrel sauna cover follows a rounded profile, while a cabin sauna cover fits a box-shaped structure. The right choice depends on the sauna's exterior shape, not only its capacity or interior seating.

A cabin cover can be easier to measure because its sides and roof create a more familiar rectangle. You still need to allow for roof pitch, door trim, and any raised features.

The flat sides of a cabin make the measurement logic simple in daily use. You can picture the cover as a sheet that folds over straight edges and corners.

A barrel cover needs enough material to cross the roof and fall down the sides. It should not be stretched so tightly that normal movement or fastening puts constant strain on the seams.

With a barrel, the curve adds distance that a flat width measurement will miss. The fabric has to follow the arc before it can hang down the wall boards.

That extra travel is why diameter matters for barrel models. A cover sized only to the floor footprint will often sit too high on the sides.

The ends add another layer of difference. A cabin end is square and predictable, while a barrel end is round and needs a cut that respects that curve.

Fastening also differs in practice. Cabin covers often rely on straps that pull straight down, while barrel covers may need fasteners that hold fabric in place over a curved surface.

Consider care and set up too. A shaped barrel cover usually goes on in a set order over the roof, while a loose cabin cover may need more pulling and smoothing at the corners.

Neither type works well if dried wood is left under a damp cover for long periods. Lift the cover to check for moisture after rain, and let the exterior dry before refitting it.

Before choosing a cover, compare the sauna shape with the cover shape first. Capacity charts and interior dimensions will not guide you to a close fit on the outside.

Measurement or featureBarrel saunaCabin sauna
Main width measurementOutside diameterOutside width
Roof shapeCurvedFlat or pitched
End shapeRounded or curvedRectangular
Main fit concernEnough fabric over the arcEnough room around corners and roof edges
FasteningStraps, buckles, or fitted endsStraps, buckles, or fitted corners

For broader equipment ideas, see our guide to best barrel sauna accessories. Accessories can change the clearance a cover needs, so measure with permanent items installed.

How much extra room should a sauna cover have?

A cover should have enough extra room to pass over the sauna without pulling tightly, but it should not be so oversized that it pools on the ground. The best amount depends on the cover's design and fastening points.

Do not add a large, arbitrary allowance to every measurement. Instead, compare your sauna's dimensions with the cover's finished size and look for the direction in which the cover is meant to sit.

A cover may be labeled by length and width, but those numbers do not always describe the same part of the sauna. Ask:

  • Does the stated width run across the roof or along the side?
  • Is the cover designed for a curved barrel profile?
  • Does the cover include fitted ends?
  • Where do the straps or buckles sit?
  • Will the bottom edge clear the ground?
  • Is there room for a chimney or vent?

If the cover has a fitted shape, follow its measurement guide. If it is a loose outdoor cover, focus on the widest route over the roof and the amount of side drop.

Should you choose a cover or a barrel sauna roof?

Choose a removable cover for flexible, temporary protection, and consider a permanent roof when the sauna will stay outdoors in a wet or snowy location. The two options can also work together if the cover fits over the roof structure.

A cover is useful when you want to uncover the sauna regularly or store it during part of the year. It can also help shield the exterior from direct exposure when the sauna is not being used.

That flexibility suits homes where the sauna is used often. You can remove the cover in minutes, heat the sauna, and replace it once the exterior has cooled.

A permanent roof suits a sauna that rarely moves and faces steady rain or snow. It stays in place through changing weather and does not need daily handling.

For wood-care advice, see staining an Almost Heaven sauna.

A roof offers a fixed layer of protection, but it changes the sauna's outside dimensions and may affect how a cover fits. Measure after the roof is installed if you plan to use both.

The roof can add height at the ridge and width at the eaves. A cover that fit the bare sauna may then sit too tight over the roof boards.

That added size can also change where straps land. Check that fasteners can close without pulling seams or trapping fabric against sharp edges.

Read our guide to choosing a barrel sauna roof before treating a cover as the only weather solution. The right setup depends on rainfall, snow, wind, shade, and how often you can inspect the wood.

Think about upkeep in each case. A cover needs regular checks for shifted straps, pooled water, and rubbing at trim points.

A roof needs checks for fasteners, gaps, and debris along the edges. Both approaches work best when you inspect the sauna on a simple schedule through the year.

How should you fit and secure an Almost Heaven sauna cover?

Fit the cover over a dry, clean sauna, then center it so the roof and side drops are even. Secure the fastening points without pulling the fabric so tightly that the seams remain under constant strain.

Avoid trapping wet leaves or standing water beneath the cover. Moisture needs a way to escape, and the wood should be dry before long-term coverage.

Check the cover after windy weather. Look for shifted straps, exposed roof boards, pooled water, and rubbing around door trim or roof edges.

A cover should not block safe access when the sauna is in use. Remove it fully before heating the sauna unless the cover manufacturer specifically gives different instructions.

Do not allow fabric to sit against hot stove components or a chimney.

If the sauna is still being assembled, follow a clear sequence with our guide on how to assemble a barrel sauna. Measure the finished structure after assembly because the final trim and roof position can affect the cover fit.

Useful products for a covered sauna area

These products solve nearby setup needs, but they do not replace a correctly sized sauna cover.

The Door Buddy Baby & Cat Door Latch has an adjustable strap, hook, and latch. It is intended for babies and toddlers ages 0 to 2, works with bifold, sliding, pocket, and double doors, and uses 3M adhesive on a clean, flat door and frame.

Do not install it on drywall, and allow 48 to 72 hours for the adhesive to cure.

The Dynamic Saunas Barcelona 1-2 Person Infrared Sauna has natural Canadian hemlock wood, 6 low EMF carbon PureTech infrared panels, a 36 in x 32 in x 67 in interior, and a temperature range up to 135°F. It uses a standard 15-amp, 120-volt plug and is intended for indoor use.

The Gas One GS-3400P Propane or Butane Stove uses either one 8 oz butane cartridge or a 16.4 oz propane cylinder, with fuel sold separately. It includes a propane converter regulator, automatic piezo-electric ignition, an adjustable heat dial, and pressure-related safety shutoff features.

What cover mistakes should you avoid?

The most common mistake is buying by the sauna's interior capacity instead of its outside shape. A 2-person barrel and a 2-person cabin can need very different cover dimensions.

Interior capacity tells you how people sit, not how fabric drapes. Outside length, diameter or width, and height tell you what the cover must actually cover.

Avoid these errors:

  • Measuring the flat base but not the barrel's widest diameter.
  • Forgetting roof trim, vents, or a chimney.
  • Choosing a cover that reaches the ground and collects water.
  • Stretching a loose cover tightly over the curved roof.
  • Covering damp wood for long periods.
  • Leaving the cover on during heating.
  • Assuming a universal cover has rounded ends.
  • Measuring before assembly is complete.

Each error has a plain cause in daily use. Measuring the base skips the widest part of a barrel, so the cover ends up short where it matters most.

Forgetting trim and vents creates pressure points. Fabric pulls against a raised fitting, wears at the edge, and can shift the whole cover off center.

A cover that reaches the ground can soak up rain and hold dirt against the lower boards. A shorter drop that clears the ground usually stays cleaner and dries faster.

Stretching a cover over a curve puts steady strain on seams. That strain grows worse when straps are tightened or when wind moves the fabric.

Covering damp wood traps moisture against the exterior. Lift the cover after wet weather and let the sauna dry before closing it again.

Leaving a cover on during heating is a safety issue. Remove it fully before you use the sauna unless the cover maker states otherwise in writing.

Assuming a universal cover has the right ends leads to gaps at round walls. Check the end cut and the fastening layout against your sauna before you order.

Measuring before assembly is complete means trim and roof pieces are missing from your numbers. Take your final measurements after the sauna is built and all permanent parts are in place.

Take photos of the sauna from the side and end while measuring. Those views make it easier to compare the structure with the cover's shape and fastening points.

Keep the photos with your measurements when you shop. They help you picture how fabric will fall over the roof and where straps will sit.

How to choose the right Almost Heaven sauna cover

Pick a barrel-specific cover when your Almost Heaven sauna has a rounded roof and end profile. Match its length to the full outside sauna length, then confirm that the width or diameter gives enough fabric to cross the roof and fall down both sides.

A barrel-specific shape helps the cover settle without pulling at the ridge. The fabric can follow the arc and hang more evenly on both walls.

Pick a cabin-style cover when the sauna has straight walls and a rectangular roof. In both cases, check the finished dimensions, fastening layout, and clearance around vents or chimneys before ordering.

For a cabin, pay close attention to corners and roof edges. A cover needs room to turn those angles without cutting across trim or door surrounds.

Check where straps and buckles sit on the finished cover. Their position decides how much side drop you need and whether the bottom edge will clear the ground.

Clearance matters above the roof as well. A chimney, vent, or raised trim can push fabric up and leave the wall boards exposed below it.

Think about how you will use the cover week to week. If you remove it for every session, a lighter fit with simple fasteners may suit you better than a tight shaped cover.

If the sauna sits unused for longer stretches, a closer fit may protect the exterior more fully. You still need to check for trapped moisture and adjust the cover after storms.

Set up starts with a clean, dry sauna. Center the cover over the roof first, then work the fabric down each side before you close the fasteners.

Do not pull straps so tight that seams stay under strain. A snug cover should hold its place without forcing the fabric into sharp folds at the edges.

After the first week, inspect the fit again. Look for shifted straps, exposed boards, rubbing at trim, and water pooling where the fabric meets the ground.

If you are planning the structure itself, read how to build a barrel sauna first. A measured cover protects the finished sauna more reliably than a cover chosen from the interior seating capacity alone.

Frequently asked questions

How do I measure for an Almost Heaven sauna cover?

Measure the sauna's outside length, then measure its width or barrel diameter at the widest point. For a barrel sauna, also note the curved roof and the shape of both ends.

Use those measurements to compare the cover's stated dimensions, allowing enough room for the cover to reach below the roofline.

Can I use a rectangular cover on an Almost Heaven barrel sauna?

A rectangular cover may work only if its dimensions and shape leave enough material to reach around the barrel without pulling tightly over the curved roof. A barrel-specific cover usually gives a closer fit because it is designed around the sauna's rounded profile.

Should an Almost Heaven sauna cover reach the ground?

An Almost Heaven sauna cover should cover the roof and upper walls without dragging heavily on the ground. A cover that is too short can leave wood exposed, while excess fabric can collect water, dirt, and snow.

Compare the cover length with the sauna's outside wall height before buying.

Does a sauna cover replace a barrel sauna roof?

A sauna cover and a barrel sauna roof serve different purposes. A roof is a more permanent weather shield, while a cover is a removable layer used when the sauna is not in use.

Choose based on your climate, installation site, and how often you want to remove the protection.